Reasons Your fiat 500 replacement remote key cost punto replacement key, blog post from ramirez-hoffman.thoughtlanes.net, 500 Key Fob Won't Work

A fiat punto keys 500 key fob is a great way to unlock the doors and get started the car. However, there are many reasons why the fob won't be working. These include a dead coin battery damage to the receiver module, issues, and interference.

This listing is for an NEW replacement Fiat Flip Key Remote that appears similar to the Ilco brand. It has to be professionally programmed (click here to find local automotive locksmiths). Includes lock, unlock, and trunk buttons.

Dead Coin Battery

The most common reason your 500 key fob doesn't work is an inactive battery. Modern key fobs have a limited range of operation and must be within just a few inches of the vehicle to work. If you are further away from your car and press the keyfob button, it will not respond, and display the message "Key Fob Not Detected".

If this happens If this happens, replace the battery in the coin-cell (Part Number CR2032) by a brand new one of a reputable brand such as Panasonic Duracell or Energizer. They are typically available at your local hardware store or online.

You can test the battery of your coin-cell by pressing the buttons while standing near your Fiat 500. The car will flash its parking lights, and the key fob should be able to operate the lock and unlock switches.

If the key fob won't work after replacing the battery, it might be damaged by water, which prevents it from communicating with the receiver module in your car. Water damage can occur in many ways, including an easy splash or submerging the key fob saltwater at the beach. If you believe your fob was exposed to water, you can place it in a rice bag to draw out the moisture. If this doesn't work, your fob will probably need to be reprogrammed by an experienced auto locksmith or by the dealer.

Water Damage

The fob does have rubber seals that keep water out of the chip's electronic circuit the device, submerging it into the ocean or washing it in a machine could cause water damage. Saltwater can be particularly harmful to the circuit board of the fob which causes it to short out and eventually end up dying. It's not the best idea to get the fob wet but don't give up when you accidentally drop it in water or Fiat Punto Replacement Key fail to remove it from your pocket.

First take the battery off the fob. Before replacing the battery clean the electronic chip using isopropyl or similar products. Check the fob to see if it is working. If the key does not function, it may need to be programmed again. This is typically done by a professional or dealer auto locksmith.

If your key is a bit older and has not been programmed for your vehicle You will need to replace it completely. This is an easy process that can be completed by a professional automotive locksmith. The locksmith will require the key to be cut to match your vehicle's ignition. They will also need to program the fob into your vehicle's system. This is a cheap and quick procedure that can be completed the same day.

Receiver Module Issues

One of the main reasons your 500 key fob won't be functioning is because it's out of range. The remote has a maximum range of 30 feet, so should you be too far away from your vehicle, it won't respond to your commands. This can be fixed by moving it closer to your vehicle until it starts responding.

If your fob doesn't work after you replace the battery in the coin, also called a "button", "watch" or "button", Fiat Punto Replacement Key it may be due to a malfunction on the circuit board inside. Reprogramming the fob is usually the solution to the issue. The instructions are available for the majority of vehicles on YouTube or in the owner's manual.

It is possible to replace the metal clips that hold the battery of your coin in place. If they become loose, it can stop your coin battery from being properly seated, causing your remote to malfunction.

In rare cases it is possible that the fob will become disconnected from your vehicle because of software or hardware issues. This issue can be fixed by visiting your local auto-locksmith or dealer to reprogram your key fob. In certain instances, the software may also require reinstallation in your body control modules.

Interference

In addition to a dead coin battery, the key fob may not be able to transmit or receive signals due to interference. This may happen if the keyfob is located in close proximity to a radio transmitter, like a cellphone or radar detector. Other reasons the key fob might not work include a poor connection to the buttons, damage to the internal chip or water damage.

If the key fob failed to work one day in the middle of the night and you've tried everything you can do at home to solve it e.g. You could have a malfunctioning 500 receiver module after you've tried replacing the battery, reprogramming, and using a spare key fob. The receiver module is situated under the dash and receives the radio frequency signals from the key fob. It then converts them into electronic commands that the vehicle interprets.

There is a simple way to reset the 500's on-board system, including the keyfob. Disconnect the battery for 15 minutes by removing first the negative cable, then the positive cable. Reconnect the battery. This will erase any remaining electricity, and restart the car's computer. This can help get your key fob to work again. If the problem persists you should seek out an expert technician. They will be able to determine the root of any problems.