Reasons Your Fiat 500 Key Fob Won't Work

A fiat doblo key programming 500 key fob is a handy way to open the doors and start the car. However, there are numerous reasons why the fob won't be functioning. This includes a dead battery and water damage, as well as issues with the receiver module, and interference.

This listing is for an NEW replacement Fiat Flip Key Remote - an exact replica of the Ilco brand that needs to be programmed professionally by a local automotive locksmith (click here to search for a Locksmith Search). It includes lock, unlock, and trunk buttons.

Dead Coin Battery

The most common reason your 500 key fob will not work is an inactive battery. Modern key fobs come with a limited operating range, and must be within a few feet of the car to operate. If you are further away from your vehicle and push the keyfob button it won't respond and display the message "Key Fob Not Detected".

If this happens, simply replace the battery of your coin cell (Part number CR2032) with a fresh one from a reputable manufacturer like Panasonic, Duracell, or Energizer. They are available at your local hardware store, or on the internet.

You can test the battery of your coin-cell by pressing the buttons while standing near your fiat panda key fob replacement, imoodle.win, 500. The parking lights should blink and the key fob will operate the lock and unlock switches.

If the fob's remote doesn't function after replacing the battery, it might have water damage that prevents it from communicating with the receiver module inside your vehicle. Water damage can occur in a number of ways, ranging from a light splash to submerging the fob in salt water at the beach. If you believe your fob was exposed to water, put it in a rice bag to draw out the moisture. If that doesn't work, your fob may need to be reprogrammed by an experienced auto locksmith or by the dealer.

Water Damage

Water damage can happen if you immerse the fob into the ocean or wash it in a washing machine. Saltwater can cause the circuit board to short and then cease to function. The fob getting wet is not an ideal idea however, if you drop it into the water in a cup or forget to remove it from your pants pocket before running the washing machine Don't give up hope.

First remove the battery from the fob. Before replacing the battery clean the electronic chip with isopropyl, or a similar product. Then test the fob to verify if it is working. If the fob doesn't work, it may need to be changed. This is usually handled by an auto locksmith or dealer.

If your key is old and is not programmed for your car then you'll need to replace it completely. A professional automotive locksmith can complete this simple process. The locksmith will require the key to be cut to match the car's ignition. They will also need to reprogram the fob in the system of your car. It's a simple and cost-effective procedure that can usually be completed within the next day.

Receiver Module Issues

Your 500 key fob might not work because it's out of range. The remote usually has a range of 30 feet or fiat panda key fob replacement less, and if it's too far from your vehicle, it won't respond to your commands. It's easy to remedy this by moving your remote closer to your vehicle until it responds.

If you've replaced the coin battery (commonly called"button" or "button" or "watch") and your fob still won't work, Fiat Panda Key Fob Replacement it could have an internal circuit board problem. In the majority of cases, reprogramming your fob will fix the problem. You can find the instructions for most vehicles on YouTube or in the owner's guide.

It could be necessary to replace the metal clips that hold the coin batteries in place. If they loose tension, it can prevent your coin battery from being properly seated, causing your remote to malfunction.

In rare cases the fob may be out of alignment with your vehicle because of hardware or software issues. You can fix this problem by visiting your local dealer or auto-locksmith to reprogram your key fob. In certain instances the software may require reinstallation to your body control modules.

Interference

In addition to a dead coin battery the key fob could not be able to transmit or receive an signal due to interference. This can happen when the key fob is located near the radio transmitter (cell phones, radar detectors) or another source of electromagnetic radiation. The key fob may not function due to a bad connection with the buttons, water damage or damage to the internal chips.

If your key fob suddenly stopped working, or if you have tried everything at home to solve the issue (e.g. replacing the battery, reprogramming it and using the spare key fiat 500 key fob, you could have a damaged receiver module on your 500. The receiver module, located beneath the dashboard, is able to pick up radio frequency signals from your key fob. It converts them into electronic commands that the vehicle interprets.

There's a quick and easy way to reset the 500's onboard system including the keyfob. Disconnect the battery 12 volt for about 15 minutes by disconnecting the negative cable first then the positive cable. Then, reconnect the battery. This will clear any residual electric current, and also restart the car's computer. This can help get your key fob to work again. If the issue continues you should seek out an expert technician. They can identify the root of any problems.