Reasons Your fiat 500 spare Key cost 500 Key Fob Won't Work

A key fob for the fiat ducato remote key programming 500 makes it easy to open doors and start your car. However, there are numerous reasons why the fob won't be working. This includes a dead coin-battery or water damage, problems with the receiver modules, and interference.

This listing is for a NEW replacement fiat 500 key Flip Key Remote that looks like the Ilco brand. It has to be professionally programmed (click here to search for local locksmiths for your vehicle). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is probably the most common reason for your 500 key fob not functioning. Modern key fobs have a limited operating range, and must be within only a few feet from the car to operate. If you're far away from your vehicle when you press the key fob button, the car won't respond and will display the "Key Fob Not Detected" message in the instrument cluster.

If this happens If this happens, replace the battery in the coin-cell (Part Number CR2032) by a brand new one of a reliable brand, such as Panasonic Duracell or Energizer. They can be found in your local hardware store, or on the internet.

You can test the battery on your coin-cell by pressing the buttons while you're standing close to your Fiat 500. The car should flash its parking lights and the key fob should operate the lock and unlock buttons.

If the fob's key doesn't work after replacing the battery, it might be damaged by water, which prevents it from connecting to the receiver module in your car. Water damage can happen in many ways, including an easy splash or submerging the key fob into saltwater at the beach. If you suspect that your fob has been exposed to water, try putting it in a dry rice bag to pull the moisture out. If this isn't working, you'll need to have your fob reset by an auto locksmith or dealer.

Water Damage

The fob does have rubber seals that keep water out of the electronic chip inside, submerging it in the ocean or washing it in a machine can cause water damage. Saltwater can cause the circuit board to short and eventually end up dying. Getting the fob wet is not an ideal idea, but if you drop it into a glass of water or do not remember to remove it from your pocket before you run the washer Don't give up hope.

Remove the battery first. Clean the electronic chip with isopropyl alcohol or a similar product and then dry it thoroughly before replacing the battery. Check the fob again to check if it's functioning. If the key does not work, it may need to be reprogrammed. This is typically handled by a professional or dealer auto locksmith.

If your key is older and not programmed to work with your vehicle, you will need to replace it completely. This is a simple process that can be carried out by a professional automotive locksmith. The locksmith will require the key cut to match your car's ignition. The locksmith also needs to reprogram your fob in the vehicle's system. It's a simple and cost-effective procedure which can be completed on the same day.

Receiver Module Issues

Your 500 key fob may be inoperable because it's out of range. The remote usually has an operating range of 30 feet or less, Fiat 500 Spare Key Cost and if it's too far away from your car it will not respond to your commands. This can be fixed by moving it closer to your vehicle until it starts responding.

If your fob isn't working after you replace the battery for the coin, also called a "button", "watch" or "button" It could be due to a problem with the internal circuit board. Reprogramming your fob can resolve this issue. You can find the instructions on how to do this for all automobiles by searching YouTube or reading the owner's manual.

You may have to replace the metal retaining clips that keep the coin battery in place. If they loose tension, they could stop the battery from sitting properly and cause your remote to malfunction.

In rare instances, the fob can become out of connection with your vehicle as a result due to hardware or software issues. This can cause a major issue, but you are able to often fix this by visiting a local dealer or Fiat 500 spare key cost auto locksmith to reprogram your fob. In some cases it is possible that the software will need to be reinstalled in your body control modules.

Interference

Interference can also cause the key fob to not be able to receive or transmit a signal. This is possible when the key fob is in proximity to an electronic radio transmitter (cell phones and radar detectors) or any other source of electromagnetic radiation. Other reasons the key fob may not function may be a lack of connection to the buttons, damage to the internal chip or water damage.

If your key fob suddenly stopped working, or you've tried everything at home to solve the issue (e.g. You may have a faulty 500 receiver module If you've tried replacing it with a battery, reprogramming, or using a spare key fob. The receiver module is situated under the dash and is able to pick up the radio frequency signals from the key fob. Then, it converts them into electronic commands that the vehicle interprets.

Fortunately, there's an easy method of resetting all of the onboard systems in your 500 device, including the key fob. Disconnect the battery of 12 volts for approximately 15 minutes by removing the negative cable and then the positive cable. Reconnect the battery. This will eliminate any remaining electric current, and also restart the car's computer. This can help get your key fob working again. If the issue persists, you should consult an expert technician. They'll be able diagnose the exact cause of your problem.